Popular Seem Edits for the V710, E815, V3C and V3M....
While each phone may have similar numbered seems (example
2742), the same offset/bit combo may not work consistently across all phones
which have that seem. This means that a particular seem/offset/bit
combo may work on one phone, but not another. This inconsistency is also
found across different firmware levels of the same phone.
This list represents a collection of seem edits that work on
the various phones, but again, you might find some that work on one model phone
with a specific firmware, but not work on another, or a different firmware
level. Phones using the Verizon UI also bring additional
complications into the mix.
Seem edits can be dangerous, and can render your phone
inoperable, so proceed with caution and always keep a backup of your un-edited
seems!!
Detailed SEEM information is available at NuclearElephant.com's
V710 seem info page , NuclearElephant's
E815 seem info page and superwombat's page. Thanks to superwombat and zaduma over on CDMAFORUMS.COM for information about TELUS V710 seem edits!!!
evade has been keeping a list of seems, offsets and bits at -> http://motorola.szczuka.org/
Every seem edit requires you to know the appropriate Seem number, Bytes (h), Record number, Offset and Bit to change. The following will give you
that information....
UPDATE: For Bytes (h) value...
Entering 0000 as the Bytes (h) value causes P2KSeem for V710 to load the
entire seem file (all offsets) from the phone. In the past, we'd
enter a number (in hex) such as 7A or 90, which tells P2KSeem for V710 to load
only that range or only a subset/section of offset data.
NOTE: Some of these might already be set as default...
To use these in the Seem Edit Process... Use Record 1, Bytes (h) 0000
For the V710 Seem is 041A
For the E815/V3C/V3M Seem is 2742
Note: Using an improper byte (h) value or Seem
number will result in the
inability to load the seem file from the phone. Saving to Phone with improper
Seem number and Bytes (h) could possibly completely mess up your phone!!
NOTE: while "Checking the Box" or "turning ON" the bit usually enables, there are a few
cases in which
"UNCHECKING the Box" or "Turning OFF" the bit enables the feature!!!
So pay attention!
Make sure you
have the latest P2KSeem4V710 so you can see
the descriptions/values while editing!!
evade has kept a more detailed listing of the 2742 Seem at -> http://motorola.szczuka.org/2742.php however the values on that list may or
may not work to the phones using the Verizon UI (like the V3C, V3M, K1M)...
Offset & Bit - Description - value...
Offset 6A Bit 0 - Bluetooth Or USB file transfer in MPT (plus E815 OBEX)
- check to enable.
Offset 62 Bit 5 - Enable editing of PIX servers - check to enable. (For
details see... PHP
Pix Place Server available!) Note: this does not work on the Verizon V3C/V3M firmware.
Offset 75 Bit 5 - Transflash Copy/Move Option - check to enable
Offset 1D Bit 3 - Motorola Startup Animation - check to enable, uncheck for
"logo only"
Offset 23 Bit 5 - Roaming Call Guard(Settings > In Call Setup > Call Guard) -
Check to enable.
Offset 29 Bit 1 - Menu Items: Settings > Security > Lock Keypad - check to
enable (to use on V710/E815 press [menu] *, on V3C press [CLR]
*)
Offset 31 Bit 0 - Motorola Shutdown Animation - check to enable.
Offset 06 Bit 1 - Ringtone: Siren - check to enable
Offset 38 Bit 1 - Ringtone: Continental - check to enable
Offset 38 Bit 2 - Ringtone: Classic - check to enable
Offset 38 Bit 3 - Ringtone: Attention - check to enable
Offset 3B Bit 0 - Ringtone: Moonlit Haze - check to enable
Offset 4B Bit 0 - GPS icon indicator - Check for CrossHair, Uncheck for Satelite
Offset 5A Bit 7 - File Access in QPST - Check to Unlock, Uncheck Lock
Offset 5e Bit 6 - Menu Items: Picture Setup > Shutter Tone > None as Choice -
Check to allow NONE, uncheck to not
Offset 5F Bit 7 - Menu Items: Video Setup > Video Quality - Check to have
choice, uncheck to Not.. NOTE: this setting has no use,
as the video quality defaults set to HIGH.
Offset 74 Bit 7 - Digital Indicator (1X or D) - Check for 1X, Uncheck for D
Offset 75 Bit 4 - Apply As Ring Tone Menu Option - Check to Disabled, uncheck to
Enabled
Phone ID String Edit for using
Verizon phones with MPT... Thanks to
Raalph253 and the New Seem found thread.... Doing this seem edit adds the missing "M"
to the Identification string in the phone. Once completed, MPT's
"auto-detection" of the phone will identify it as V710M, E815M, V3cM or V3mM and MPT
will be configured accordingly (i.e. show the Multimedia Studio Icon).
Note: if you do not wish to perform this seem edit, you can manually cofigure
MPT for your phone, or Edit the Detect.inf as outlined HERE
NOTE: the Offset 6A Bit 0 seem edit listed
above is still
required to make the MultiMedia Studio feature of MPT actually work!!!
For the E815 this
would be Seem 2827, Record 1, Bytes (h) 22, Offset 0008,
"check the boxes" for bits 0-2-3-6 and "uncheck the boxes" for Bits 1-4-5-7. PRE-EDITED SEEM for E815m -> 2827_0001-E815m.seem
For the V710 this would
be Seem 04FF, Record 1, Bytes (h) 22, Offset 0008, "check the boxes" for bits 0-2-3-6 and "uncheck the boxes" for
Bits 1-4-5-7.
For the V3C (with .02 or .03 firmware) this would be Seem 2827, Record 1, Bytes (h) 22, Offset 0006, "check the boxes" for bits 0-2-3-6 and
"uncheck the boxes" for Bits 1-4-5-7. PRE-EDITED SEEM for V3Cm -> 2827_0001-V3Cm.seem
For the V3C (with .04 firmware),
the ID STRING Changed from just "V3C" to "V3C REV2"... which impacts MPT's phone
ID check... So just Adding the Missing M is not enough, you must also remove the
REV2... More notes and an example to help explain to be added
later... PRE-EDITED SEEM
for V3Cm -> 2827_0001-V3Cm.seem
For the V3M this would be Seem 2827, Record 1, Bytes (h) 22, Offset 0006, "check the boxes" for bits
0-2-3-6 and "uncheck the boxes" for Bits 1-4-5-7. PRE-EDITED SEEM for V3Mm -> 2827_0001-V3Mm.seem
For the Krzr K1M this would be Seem 2827, Record 1, Bytes (h) 22, Offset 0006, "check the boxes" for bits
0-2-3-6 and "uncheck the boxes" for Bits 1-4-5-7. PRE-EDITED SEEM for K1Mm -> 2827_0001-K1Mm.seem
Editing the Banner Seems... process for removing or changing the "Verizon
Wireless" words from the inside and outside LCD.
Modifying the V710/E815/V3C Internal Banner
Note: For the Verizon V3C the text from the internal banner is displayed on
the outside screen so there is no separate External banner mod for the
Verizon V3C.
Modifying the E815 External Banner <- Also for Alltel V3C
Modifying the V710 External Banner
Verizon V3C/V3M Specific...
These use Seem 2742, Record 1, Bytes (h) 0000
Offset 7B Bit 3 - Vibrate THEN Ring part1 - Uncheck to enable
Offset 7B Bit 4 - Vibrate THEN Ring part2 - Check to enable
With Bit 3 & 4 set this way, you will have Vibrate THEN Ring available as a ring style
Offset 7B Bit 2 - Moto UI Style Ring Control Part 1 - Uncheck to enable
Offset 7B Bit 7 - Moto UI Style Ring Control Part 2 - Check to enable
With
Bit 2 & 7 set this way, you will have volume 1-7 like the normal Moto UI instead
of Low thru High
Offset 94 Bit 7 - VZW V3C .04 outside LCD - Check to be ORANGE, Uncheck for Graphic
V710 Specific... (Not tested on V3C or E815) These use Seem 041A, Record 1, Bytes (h) 0000
Offset 64 Bit 5 - Remove the RE: & FW: from text messages
being sent part1 - Uncheck
Offset 64 Bit 6 - Remove the RE: & FW: from text messages
being sent part2 - Uncheck
Thanks to cr9c1
Most phones... (tested on V3C, E815, V9M, K1M..
Seem 2784 0001 bytes A : 4 digit User Lock
Seem 2786 0001 bytes E : 6 digit Master Security Lock (MSL)
Seem 0055 0001 bytes E : 6 digit Service Programming Code (SPC)
UNTESTED 2742 Seem edits
(I have NOT personally tested these yet, but I believe they will work on the E815 and Alltel V3C...
They may or MAY NOT work on the Verizon V3C/V3M firmware!!)
Offset 8D Bit 6 - Menu Item: Time & Date Menu -
Check to enable
Offset 16 Bit 6 - Menu Item: Loud Detail > Roam Calls - Check to enable
Offset 3D Bit 1 - Menu Item:
Enable Text Message Delivery Notification-
check to enable
Offset 49 Bit 5 -
Set Delivery Report Default for new messages - Check =Yes, Uncheck = NO
Offset 7D Bit 5 -
Changes backlight times to 20, 40, 60, seconds and Continuous =ON
Offset 33 Bit 6 -
Menu Item: Backlight Color Option: Red, Green, Orange - Check to enable NOTE: the phone only
has a WHITE backlight, so while the menu option shows, it has no effect.
Offset 40 Bit 6 - Enables Alltel firmware to keep 100+ texts - Check enables.
Offset 27 Bit 0 -
Outer LCD Text (Bit ON) / Graphics (Bit OFF)
I have also compiled a list of addtional seem edits posted by various users in various thread... SEEM1.TXT they may or may not work on all phones. I eventually hope to add them to this to this page... but until I do, at least you have this text file too...
Free Hit Counter
|