How to Flash your phone's firmware (using RSDLite).

I know there are already some good guides on flashing your phone with the different firmwares, but each walks you thought as part of some "Bigger process"... so its more geared towards that process, lists all the pre-reqs for that process, etc..

This is the straight GENERIC process to flash your phone with ANY firmware....   It is based upon -> Flashing a Verizon V3c to Alltel which was part of a guide to flash to the Alltel firmware, as such, contained extra pre-reqs and the other steps to make the Alltel V3C firmware work on Verizon phones.

WARNING: Flashing with firmware not intended for your particular phone could render it useless or inoperable and it may NOT be possible to recover.  Please be sure to only use flash files meant for your phone/carrier, or that you know will work on your phone.

WARNING: Flashing with firmware from a different wireless carrier (example: Flashing a Verizon phone with Alltel firmware, and wanting to still use it on Verizon's network) may either BRICK YOUR PHONE, OR just require additional work to get all features (i.e. data services, WAP, MMS Messaging, Get-It-Now) working again.  Please be aware of what is involved BEFORE you flash with another carrier's firmware!!  

WARNING: If you flash your phone with firmware from a different carrier, your current wireless carrier will NO LONGER support you, and will most likely void any warranty on your phone.

WARNING: In most cases, flashing will erase all personal data, contacts, pictures, ring tones, games, applications, etc.  stored in the phone's memory.  Please be sure to back up this information PRIOR to flashing.  (NOTE: Due to Get-It-Now and BREW, it may not be possible to backup games/applications installed on your phone.)

NOTE: there are Upgrade Flash files and Monster Flash files available.  Monster Flash files will completely erase and re-write your phone's firmware and file system, removing all traces of the previously installed firmware.  It will revert your phone to a "fresh out of the box" state.  Use an Alltel Monster Flash on a Verizon phone, and you've turned your phone into the same thing as a phone "Fresh out of the box" from Alltel.    UPGRADE Flash Files leave the current file system in place, and put the upgraded files onto the phone.  In many cases this results in "hybrid" firmwares, or "left over files" still on the phone.  Upgrade Flash files will not revert you to a "fresh out of the box" state.  So if you are trying to recover from a catastrophic failure, you'll want to use a Monster Flash File if one is available.

Required... if you were refered to this page by another process, you may already have these pre-req's in place.

1.  USB Cable (see the FAQ)
2.  Install the Motorola USB Modem drivers.
3.  Install and configure Motorola RSDLite. Version 4.1 recomended.
4.  Firmware flash file..  (obtain from http://www.humpa.com/vzw or http://ryfiles.com/flash or Phone Encyclopedia link at phonenews.com)

The Process...

NOTE: if trying to recover a phone by reflashing, you may need to put your phone into Boot Loader mode... this is usually accomplished by pressing/holding  * and # keys while using the power button to turn the phone "on".

NOTE: When tryinng to recover a V3C/V3M/V9M/K1M or other phone that uses a USB Mini-B or MicroUSB cable, to get into Boot Loader Mode... you may need to unplug the phone, remove the battery, insert the battery, hold the * and # keys while connecting the USB cable.

Get Started...

Install the software and drivers as listed in the requirements section above.  Download/unpack the firmware file you wish to use on your PC.

Unplug your phone from the PC, power it off, then back on, and re-connect it to the PC.  

FLASH THE PHONE's FIRMWARE...

Please be sure your battery is fully charged!  You do not want to run the risk of the battery dying mid flash!

Remove any MicroSD or Transflash cards from the phone. Failure to do so on some firmwares (like Vivo) may result in the phone being in USB Mass Storage Device mode after flash, and programs like MPT, PST, MFF, etc will not be able to connect to the phone.

Start RSDLite by going Start -> Programs -> RSDLite vX.X -> RSDLite

It will launch and show your phone connected in the bottom section

Example Screen Shot -> RSDLITE1.jpg

If your phone is not listed, wait a few moments until all the drivers are loaded, then click the SHOW DEVICE button.

Click the ... button to the right of the File Name box.

IN the "OPEN" dialog box, navigate and select your flash file. Click the OPEN button.

The File Properties section should populate.

Click the Start button. 

While the flash process is in progress, you will see feed back in the Status and Progress columns.

NOTE: The first time you flash your phone, the Add New Hardware Wizard may run and try to install the drivers for the FLASH INTERFACE.  If it does not find the driver automatically and you used the MotoDev drivers, or have installed Motorola Software Update (MSU) on your computer,  point the add new hardware wizard to C:\Program Files\Common Files\Motorola Shared\MotPCSDrivers.

When the flashing process is complete, the Status column in the lower portion of the RSDLite program window should show Rebooting Phone, and the phone should restart itself.  Once the phone has restarted itself, RSDLite will request you power the phone on in Status Column. Make sure the phone has fully restarted and states its charging the battery.   It is now safe to disconnect the phone.

You may now exit RSDLite.

Unplug your phone from the PC. If the phone is in the powered off state, power it back on.

Perform a Master Reset, and Master Clear.  For phones with the Moto UI... On the phone...  Menu -> Settings -> Initial Setup.  Highlight Master Reset, and press the soft menu key to Select. When prompted for Security Code, enter 000000 or your phone's SPC. Press the soft menu key for OK.  When prompted to "reset all phone settings?" press the soft menu key for YES.  The phone will restart itself.  Repeat the same steps selecting Master Clear.

You are now complete.

Your phone is now successfully flashed.   You are ready to proceed to activating your phone, or any required work to make the phone functional on your wireless carrier's network.